Call Us (313) 242-1000

Organiclear WR Series Oil Based Log Home and Deck Stain

Free Shipping!



Premium Oil-Based Wood Coating System Specially Formulated for Log Homes and Wood Decks

Organiclear WR-5 is a premium exterior wood treatment that restores, preserves and enhances the natural beauty of your new or existing log home or Wood Deck.

The WR-5 offers a unique blend of deep-penetrating premium oils, resins and waxes to create for your home the ultimate long-lasting MOISTURE-GUARD™ barrier against harsh weather. To enhance wood life further, the WR-5 provides maximum protection against ultraviolet (UV) radiation damage by combining sun blockers to absorb and control UV degradation, thus minimizing wood deterioration. For investment security, the WR-5 penetrating coating will also prevent wood from cracking or peeling.

The Organiclear™ WR-5 yields a deluxe exterior finish that allows wood to “breathe” naturally through a micro porous film and prevents moisture penetration. Water beads up and rolls off the exterior wood surface. This protective coating brings out the natural grain beauty of the wood while preventing the wood from cracking and peeling. WR-5 is the perfect choice for the full realm of wood protection your home needs to stand the test of time.

  • Water Repellent System
  • Beautifies Wood Grain
  • Ultraviolet (UV) Shield
  • Allows Wood to Breathe
  • Deep Penetrating
  • Easy Solvent Clean-up
  • One-Coat Protection
  • Natural Clear and Color Stains
Exterior Uses
Organiclear™ WR-5 Premium Wood Coating and Finishes are designed to meet the tough demands of log homes, i.e. log walls, dormers, porches, decks, railings, gable ends, exterior trim, soffits, windows and doors, etc. WR-5 also produce premier results on wood siding, shakes and shingles, fences and outdoor furniture.


Color Chart
           Natural Clear                            Ivory                            Classic Honey                      Golden Oak                           Aspen
               Cedar                                 Redwood                           Chestnut                        Walnut Brown                    Saddle Brown
          Forrest Green                   Nantucket Gray


Important: Stain colors may vary due to wood type, color, porosity and application rates. It is recommended that testing be done on an inconspicuous area or sample piece of wood prior to application to determine if color is satisfactory.
Preparation Guidelines
Before Use
WR-5 Wood Coating is for exterior use only and should not be diluted. For best results, treat new wood QUICKLY (within two weeks of weather exposure) to avoid pre-weathering damage to wood surface. Prior to use, mix well with a paint stick. Routinely stir during application.
Proper Attire
To protect against skin irritation, you or your wood treatment contractor should always wear a long-sleeved shirt, long pants and goggles. Also use an OSHA approved mask to protect against inhalation of vapors. For your information and safety, please take the time to read the product label carefully before use. Before applying stain to the entire home, test on a sample piece of log from your home to verify the color and look you want.
Apply between the temperatures of 50°F and 80°F. Do not apply when hot, wet or windy weather conditions are expected within 36 hours. Always wait for moisture to dry before application.
Clean Surface
Wood should be clean and dry, unpainted and free of all loose debris including loose bark, sawdust, mud, etc. All upward-facing checks and splits in the wood surface should be filled with an exterior wood filler. Any unwanted stains, mildew, fungi or pre-weathering should be cleaned first with a power washer using one quart household bleach, one gallon of water and one pound of TSP-90 (available at your local hardware store) or non-ammoniated detergent. Rinse off completely and allow to dry.
Mill Gaze Remover

Although a brand new deck or wood surface may look clean, it has dirt, mildew, waxy residues and mill glaze.

Mill glaze is produced by high speed planes in modern lumber mills. Often the high speed planes not only plane the wood, but they crush the exterior wood fiber to create a very shiny lumber surface. The crushed fibers do not let stain and seal coatings absorb properly, causing finish failure.

Apply a deck preparation mill glaze remover product. These products are designed to clean the deck, lower the pH, relieve the surface tension and help the wood to absorb the sealer or stain evenly. This assures maximum stain absorption, prevents flaking or scaling of the coating and leads to a longer lasting job without a splotchy look.

Method of Application

Apply WR-5 liberally to dry wood to the point of saturation for maximum protection. One coat is sufficient to repel water on most wood surfaces. The preferred application methods are:

  • A quality paint brush.
  • An airless sprayer (rentable).
  • A pump-type garden sprayer.

The wood coating should saturate all checks or splits. All exposed log or timber ends should be coated several times until all wood pores are saturated.

Depending upon the method of application and the porosity, texture, and dryness of the wood, allow 200 – 400 square feet per gallon.
Drying Time
Allow 12-24 hours for drying. The temperature and humidity conditions may necessitate a longer drying period.
Use mineral spirits to clean brushes and equipment, as well as to remove drips and spatters from all surfaces. Use soap and water to wash skin thoroughly after handling material.
Cover the product when not in use. Keep in tightly-sealed containers out of reach of children. Store at room temperature (keep from freezing).
Log Home Care & Maintenance
Wood surfaces may need to be retreated every 3 – 4 years or earlier depending on weather exposure. A close inspection of treated surfaces should be done annually.

Additional information

Weight 42 lbs
Dimensions 1 × 1 × 1 in

5 Gallon Pail


Natural Clear, Ivory, Classic Honey, Golden Oak, Aspen, Cedar, Redwood, Chestnut, Walnut Brown, Saddle Brown, Forrest Green, Nantucket Gray